Tokyo Hy-Power RF Linear Amplifiers

Solid State RF Linear Amplifier Engineering  

  
 
HL-1.2Kfx
1.8 MHz ~ 28 MHz (160m ~ 10m)
Detailed Views and Specifications
HL-1.2Kfx HF Amplifier

Features:
  • Small Footprint

  • Light Weight - Lightest 750W amplifier in its class

  • Internal Power Supply

  • Simple Operation and Hookup

  • Full QSK Operation 50+WPM

  • Wide Line Voltage Operating Range 100V-250V 50-60 Hz

  • Amplifier incorporates an advanced 16bit Microprocessor that controls all the functions of the amplifier, including the protection circuits.

  • Lower cost in replacing finals compared to replacing tubes in tube-type amplifiers.


Description:

The HL-1.2Kfx is our most cost effective amplifier. It is also extremely compact and lightweight, having a small foot print, not using a lot of space in the operating station. Because the amplifier only incorporates manual band switching, this world class amplifier is very easy to connect and operate. It operates from 160m through 10 m. The amplifier has a wide line voltage operating range. It can use 100V through 250V - 50/60Hz successfully.

The amplifier incorporates the same four SD2933 RF Mosfets that are also used in the HL-1.5Kfx. The HL-1.2Kfx uses a lower supply voltage (Drain Voltage-Vd) to the finals resulting in 750W PEP and a CW output of 600 W on the HF bands. It also includes a built-in power supply and operates with line voltages of 100V-250V. The operating voltage of the amplifier can be fine tuned (via transformer tap settings) to the line voltage present at the operator’s station for maximum efficiency. The HL- 1.2Kfx utilizes manual band switching; the operator must select the proper band with every band change.

The unique air cooling duct design incorporates an efficient powerful blower fan which supplies cooling to the Aluminum Block heat sink located atop the Power Amplifier module. The fan also supplies cooling to the other internal components of the amplifier. Its quiet operation allows for even the weakest signals to be heard.

The amplifier uses a sophisticated circuit containing an advanced 16 bit microprocessor to control the normal functions of the amplifier along with the various high speed protection circuits, which will protect the amplifier from faults such as Overdrive and High SWR.

There is a front mounted meter. The meter’s function is selectable via the front mounted meter switch. It can display Power Reflected (Pr), Power Forward (Pf), Idle voltage to the MosFets (Vd), and Transmitting Current of the MosFets (Id). Mount to the right of the meter switch is the manual rotary band switch which the operator would use to select the appropriate band. There are also numerous LED indicators mounted on the front panel, Power On, High Current (Id). Warning lights include Over Drive, Overheat, Over Volt, Internal Fuse Open, and Excessive Reflective Power.

Rear controls include ALC adjustment control, Transmitter input, Antenna output, PTT keying line (STBY) RCA jack and an ALC Input RCA jack.

The amplifier is QSK capable (50wpm+) using miniature high speed Panasonic relays for T/R switching.
Specifications:
Frequency Band 1.8MHz ~ 28MHz (160m ~ 10m)
(Including WARC bands)
Operating Modes SSB / CW / RTTY
Typical RF Drive
(full output)
80W typical — 95W Max
Output Power 750W PEP Max SSB
600W CW
400W RTTY
Amplifier Class Class AB Push — Pull Circuit
RF Power Transistors ST Micro SD2933 x 4
Band Switching Manual
Power Requirement 100VAC-250VAC
50/60Hz — 1500VA
Cooling Method Forced Air Cooling
T/R Switching Miniature High Speed Relays (Panasonic/Matsushita — 5-6 ms)
Size 9.1W x 5.6H x 14.3D
Weight 33 lbs

Open PDF File Manual

Home    |    Products    |    Prices    |     Manuals & Circuits    |    Factory Tour    |    News    |    About Us    |    Contact Us    |    Tech Support / FAQ
 
 
© 2013 Tokyo Hy-Power Labs, USA